How to Vape

How to Vape? It is very easy. Our tutorials are always being updated. Learn and share your ideas.

How to Vape in a very easy way. There has been so much complicated and over-sophisticated discussion on Vaping and what it is all about. How to Vape, well, it is very easy indeed.

Demistifying all the rubbish you have heard on how to Vape. 5 minutes reading this page and you will see how easy it is. Getting to know which is your best taste will take a little longer.

 

The Basics

Atomisers 101

Atomisers can be tricky little devils, there’s no doubt about it. As long as you’re armed with the power of knowledge though, you’ll be just fine!

Atomisers are measured in resistance. This is called ohm. The higher the ohm, the higher the resistance (the more voltage it can take).  The result you achieve is relative to the battery voltage. The more volts you have, the higher resistance (ohms) you should use. This will increase your flavour and vapour. The less volts you have, the lower resistance (ohms) you should use. This will increase your flavour and vapour.

Low volts + Low ohms = Perfect vape!
High volts + high ohms = Perfect vape!
Low volts + high ohms = Less vapour, less flavour.
High volts + low ohms = Atomiser may not work, less flavour, less vapour.

Recommend -
$40 Starter Kit – Use 2ohms
VMT, VMTi – Use 1.5ohm – 2.0ohm
VV Mods – 4.5volts and below = 1.5ohm -2.0ohm
VV mods – 4.5volts and above = 2.0ohm – 4.5ohm

So now you want the simple answer right?

Well, here you go -

Use 2.0ohm atomisers and cartomisers. You’ll get good flavour and good vapour production!

Batteries 101

Once you get into Vaping, there’s a lot to get your head around and batteries are no exception.  Lets break it down for you -

Battery run time – The bigger the battery , the longer your battery will last. Battery run time is measured in mah.

280mah – $40 Starter Kit, 3hrs run time approx
650mah – VMT, 6hrs run time approx.
900mah – VMT, 10hrs run time approx.
1100mah – VMTi and VMT USB Battery, 12hrs+ run time approx.

Battery voltage – Battery voltage is measured in volts. The more volts in a battery, the more powerful your vape (flavour and vapour) can be.
Variable voltage (VV) means you can control the strength of your vape.

3.3volts – $40 Starter Kit, VMT, VMTi
3.0 – 6.0volts – VM MadMods


Basic Starter Kit Guides

Basic Electronic Cigarette Starter Kit Tutorial

One of the best introductory electronic cigarette starter kits available on the market, the Basic electronic cigarette starter kit will help you decide if Vaping is right for you.

Our Basic Electronic Cigarette Starter Kits are perfect for the beginner vaper who wants to use a smaller Vaping Vapermate. Small and sleek, these Vapermates can be carried around easily with the added bonus of looking like a little cigarillo. Of course it only releases tasty and delicious smelling vapour.

This Vapermate holds about 1.6ml, you will get approximately 3hrs of heavy Vaping before having to refill your MadMix or change batteries.

What comes in your Basic Electronic Cigarette Starter Kit?

electronic cigarette starter kit

 

 

2 x 280mah slimline batteries (Auto airflow trigger, approx 3hr run-time)
5 x Cartomisers (1.6ml capacity, 2.0ohm)
1 x USB Charger
1 x AU Power Adaptor

So how do I put my Basic electronic cigarette starter kit together?

1) Grab your batteries and put one on the charger straight away. Screw into the usb connector and connect to either your computer or use the provided power adaptor. The light will turn green when fully charged.

2) Grab a cartomiser and remove it from the packaging. Take out the silicone end plug but keep nearby as you will need it again.

3) Open up a bottle of MadMix. If you have purchased SINGLE strength, you can use straight away. If you have purchsed DOUBLE strength, you will need to mix this with your unflavoured nicotine first.

4) Slowly squeeze your MadMix into the open cartomiser end. Do this until liquid starts to drop out of the connector end. Give a quick, short blow into a tissue. What you are doing is clearing liquid from the centre air tube. Continue this process until the white wadding is soaked with liquid. Replace the silicone end plug. Suck on the cartomiser to make sure there is no liquid gurgling. If it is gurgling, give a quick short blow into a tissue again until you have good airflow.

Now your cartomiser is primed and ready to be vaped

5) Screw the cartomiser onto your battery.

6) Vape it! Just like you would a cigarette. For best results, practice with a ‘french’ inhale. Draw vapour into your mouth, then inhale into the lungs. This allows you to get the fullest flavour and most pleasant vaping experience.

How will I know when I need to change my Basic electronic starter kit battery ?

You may notice after a couple of hours use that the flavour and vapour starts to die off.  This is an indication that you’re battery is running low and needs to be recharged. When the battery is fully depleted, the blue light on the end will flash at you. It’s time to recharge!

How will I know when to add more MadMix to my cartomiser?

When you first start using your Basic electronic cigarette starter kit, it takes a bit of practice to know when to refill with MadMix. It’s a good idea to refill after about 2 hours of vaping regularly. When you remove the silicone end cap and the white filler looks dry, squeeze in a few drops around the edge (avoid the centre air tube) until it’s soaked again. That’s all it takes to refill and keep you vaping!

NB – If your cartomiser starts to taste ‘burnt’ or just doesn’t taste right anymore, it’s time to replace your cartomiser. Just toss away the dirty one, grab a new cartomiser and follow the  6 steps above in ‘So how do I put my electronic cigarette starter kit together’ that you first followed. Dead easy!

So that’s all there is to it! If you have any further questions, please let us know at info@vapingmad.com.au.

 


VMT Guides

How to Fill your VMT Atomiser

There’s a right way and wrong way to fill your VMT atomiser. Here’s the right way!

1) Remove a cartridge from the packaging.
2) Blow any fluid out of the VMT atomiser. We recommend using a tissue to wipe any excess fluid away. You only need to do this with a new atomiser.
2) Push the empty cartridge into the VMT atomiser. This pops a hole in the silicone plug on the end of the cartridge for you. You only need to do this for each new cartridge.
3) Remove the empty cartridge and take off the silicone end cap (the one you just popped).
4) Squeeze your MadMix into the cartridge about 3/4 of the way full.
5) Replace the end cap.
6) Drip a few drops of MadMix into the VMT atomiser. Try and get the middle needle pin. This primes the atomiser nicely, ready for vaping.
7) Push the filled cartridge into the VMT atomiser. Ensure the cartridge is completely flush with the top of the atomiser.
8) Wait a few seconds to allow the liquid in the cartridge to start wicking into the atomiser.
9) Vape away!

Keep an eye on the liquid level in your cartridge. When it starts to get low, just refill the cartridge again and away you go!

Cleaning your VMT Atomiser

Over time, your VMT atomiser becomes gunked up with all those wonderful MadMix flavours and needs a good clean. Here’s a simple guide to de-crudding your VMT atomiser.

1) Remove the atomiser from the battery
2) Remove the cartridge from the atomiser
3) Blow out any excess MadMix from the atomiser
4) Rinse atomiser under hot water
5) Put atomiser in a glass/cup, on it’s side
6) Pour 1 part white vinegar to 1 part water into the glass. Enough to cover the atomiser is fine.
7) Add 1 teaspoon of Bicarbonate Soda to the glass
9) Let it fizz up nicely.
10) Put thumb and forefinger over the ends of the atomiser, ensuring you’ve got some liquid in the atomiser.
11) Shake the atomiser with the ends covered.
12) Place atomiser back in the glass and let it soak for 10min – 30min.
13) Rinse atomiser thoroughly under hot water.
14) Blow any excess water out of the atomiser
15) Allow 24 hours for atomiser to dry before use or follow ‘dry burn’ instructions at own risk.

How to ‘Dry Burn’ your VMT Atomiser

You don’t always want to wait 24 hours before you can use a clean atomiser and you don’t necessarily have to. There is a quick method used to clean your atomisers but be warned, doing so could void your VapingMad warranty.

Still want to know how? Well okay, it’s simple! Just follow these steps -

1) Follow the atomiser cleaning instructions for your VMT Vapermate.
2) Screw your clean atomiser onto the battery.
3) Without vaping, press and hold the battery button for 6-8 seconds and release.
4) Wait 5-10 seconds
5) Repeat steps 3 and 4. Continue these steps until the atomiser no longer hisses and the wick is glowing red. There should also be no vapour emitting from the atomiser.
NB – This process can take anywhere between 1 – 10minutes, depending on the atomiser.
6) When you’re sure the atomiser is clean and dry, drip a couple of drops of your chosen MadMix directly onto the wick.
7) Assemble your VMT and vape away as normal.


VMTC Starter Kit Guide

VMTC E-Cig Starter Kit Tutorial

The VMTC E-Cig Starter Kit is in a league of its own! This kit is perfect for the beginner Vaper who loves simplicity and craves quality performance just as much (if not more). The VMTC E-Cig Starter Kit is great for a big Vape and showing off (or Vaping at home).

What comes in your VMTC E-Cig Starter Kit?

e-cig starter kit
 

2 x 650mah compact batteries (Manual activate button, approx 6hr run-time)
2 x VM Top Coil Clearomisers (2.4ml capacity, 2.2ohm)
2 x VM Top Coil Spares (2.2ohm)
1 x USB Charger
1 x AU Power Adaptor

 

How will I know when I need to change my VMTC e-cig starter kit battery ?

You may notice after 5 hrs of use that the flavour and vapour starts to die off.  This is an indication that you’re battery is running low and needs to be recharged. When the battery is fully depleted, the white power light (the activation button) will flash at you. It’s time to recharge!

How will I know when to add more MadMix to my VM Top Coil Clearomiser?

If you are finding that you have to tip your Vapermate upside down more frequently or you have 1ml or less in the tank, it’s time to refill! You may also notice at this time that you are occasionally getting a ‘dry’ hit which tastes burnt. This is usually an indication that you don’t have enough liquid in the tank and it’s not wicking properly.

This E-Cig Starter Kit holds about 2.4ml, you will get approximately 6hrs of heavy Vaping before having to refill your MadMix or change batteries. Your VM Top Coil has measurements on the outside up to 2.4ml. This is the maximum fill line.

How will I know when to change my VM Top Coil?

When your Vape is not tasting the way it should, maybe it tastes burnt or a muted flavor, it could be time to change your coil. Simply remove the black mouthpiece and unscrew the centre post (has a silicone cover). Replace with a new Top Coil Spare and reassemble!

So how do I put my VMTC E-Cig Starter Kit together?

1) Grab your batteries and put one on the charger straight away. Screw into the usb connector and connect to either your computer or use the provided power adaptor. The charger light will turn green when fully charged.

Your batteries have 5 click protection. They have been shipped to you in the ‘OFF’ position. To turn your batteries on, click the activation button 5 times rapidly. When the battery flashes, it is ready. Click the button again and if you see a light, it is ‘on’. Repeat the procedure to turn the battery off.

2) Grab a VM Top Coil Clearomiser. Remove the silicone end cap but keep it if you would like to use it again to keep your mouthpiece clean (handy when putting your Vapermate into your pocket or bag. Unscrew the black mouthpiece and put to the side for now.

3) Open up a bottle of MadMix. If you have purchased SINGLE strength, you can use straight away. If you have purchased DOUBLE strength, you will need to mix this with your unflavoured nicotine first.

4) Slowly squeeze your MadMix into the VM Top Coil tank. Fill up to the 2.4ml measurement line. Avoid getting liquid in the centre air tube.

5) Screw the black mouthpiece back onto the Clearomiser. Once secure, turn the VM Top Coil Clearomiser upside down a couple of times. This allows the liquid to fully soak the coil and wicks.

5) Screw the VM Top Coil Clearomiser onto your battery.

6) Vape it! Just like you would a cigarette! Just remember to hold the button while you are inhaling only. For best results, practice with a ‘french’ inhale. Draw vapour into your mouth, then inhale into the lungs. This allows you to get the fullest flavour and most pleasant vaping experience.

So that’s all there is to it! If you have any further questions, please let us know at info@vapingmad.com.au.


VMTi Guides

VMTi Starter Kit User Guide

So you’ve decided to get some bling in your life? You wont be sorry! The VMTi Starter Kit is a sturdy Vapermate that’s easy to use and maintain. We like to care for the environment every now and again so this kit doesn’t come with a paper manual. We’ve put together a little guide for you here instead!

What’s in your kit?

- A battery – It will be about 75% charged so you can use it right away! You can always grab another VMTi battery if you need to.
- An atomiser – There’s 3 parts: A tank cartridge, A 2 piece atomiser with replaceable wick. We also have the VMTi atomisers and spare wicks for individual sale.
- A USB cable + Power adaptor.
- A spare tank cartridge – You can get more VMTi cartridges if you need to in the VapingMad shop.
- A neat little carry case.

So how do you put it all together and vape?

1) Take apart the atomiser so you have 1 x tank cartridge, 2 x atomiser pieces (unscrew the atomiser so you have a wick section and a coil section)
2) Drip a couple of drops of MadMix directly onto the coil (base section). Drip 1 drop of MadMix onto the wick (top section). This helps to get the ball rolling before loading a tank cartridge.
3) Assemble the atomiser so you have 1 piece.
4) Remove the end of the tank cartridge (the part where the little silicone plug is) and fill about 3/4 full of MadMix. Replace the end cap securely.
5) Pop the tank cartridge into the assembled atomiser.
6) Screw the atomiser (with the tank cartridge in) onto the battery.
7) Vape away!

You might notice that the battery isn’t working. This is because it has a safety feature. Click the battery button 5 times quickly to turn the battery on and off. When the battery button glows while pressing it, you know it’s on!

Charging your VMTi battery

1) Unscrew the atomiser from the battery
2) Screw the battery connector into the USB cable
3) Plug the USB cable end into your computer or the wall adaptor

The battery will take a few hours to charge from the wall and a bit longer if charging from your computer.

Cleaning and Maintenance

Check out the Cleaning Your VMTi Atomiser tutorial for keeping your Vapermate in tip-top shape!

If you have any other questions about your VMTi Vapermate, just drop us a line in the Contact Us section. We’ll help you out, no worries mate!

Cleaning your VMTi Atomiser

Over time, your VMTi atomiser becomes gunked up with all those wonderful MadMix flavours and needs a good clean. Here’s a simple guide to de-crudding your VMTi atomiser.

1) Remove the atomiser from the battery.
2) Remove the cartridge from the atomiser.
3) Blow out any excess MadMix from the atomiser.
4) Unscrew the atomiser, so it’s in 2 parts.
5) Rinse each atomiser part under hot water.
6) Put atomiser parts in a glass/cup.
7) Pour 1 part white vinegar to 1 part water into the glass. Enough to cover the atomiser parts is fine.
8) Add 1 teaspoon of Bicarbonate Soda to the glass
9) Let it fizz up nicely.
10) Allow the atomiser parts to soak for 10min – 30min.
11) Rinse atomiser parts thoroughly under hot water.
12) Assemble the atomiser parts and blow any excess water out of the atomiser
13) Allow 24 hours for atomiser to dry before use or follow ‘dry burn’ instructions at own risk.

 

How to ‘Dry Burn’ your VMTi Atomiser

You don’t always want to wait 24 hours before you can use a clean atomiser and you don’t necessarily have to. There is a quick method used to clean your atomisers but be warned, doing so could void your VapingMad warranty.

Still want to know how? Well okay, it’s simple! Just follow these steps -

1) Follow the atomiser cleaning instructions for your VMTi Vapermate.
2) Screw your base atomiser part (the coil) onto the battery.
3) Press and hold the battery button for 6-8 seconds and release.
4) Wait 5-10 seconds
5) Repeat steps 3 and 4. Continue these steps until the atomiser no longer hisses and the coil is glowing red. There should also be no vapour emitting from the atomiser.
NB – This process can take anywhere between 1 – 10minutes, depending on the atomiser.
6) When you’re sure the base atomiser part is clean and dry, drip a couple of drops of your chosen MadMix directly onto the coil.
7) Check the top atomiser part (the wick). You want to the wick to be white/grey. If the ends are a bit charred, you can replace the wick with a spare. Drip a couple of drops onto the clean wick.
8) Assemble your VMTi and vape away.

Replacing your VMTi Atomiser wicks

We’ve made it so simple to bring your VMTi atomiser back to life. When your wick has reached it’s last tether, it’s time to pull it out and grab a new one. If only life was as easy!

1) Unscrew the 2 part VMTi atomiser.
2) Using a pair of tweezers, remove the old crusty, charred wick from the top atomiser part. Make sure you get all of it out.
3) Chuck it in the bin.
4) Grab a new atomiser wick.
5) Using the tweezers, hold the new wick at the base of the mesh (where it meets the white filaments).
6) Insert it into the top atomiser part where you just removed the old wick.
7) Drip a couple of drops of MadMix onto the new wick.
8) Assemble your VMTi Vapermate as normal.


VM iTaste Guides

VM iTaste Starter Kit Guide

Ahhhh so you appreciate form, function and overall sophistication? Of course you do, that’s why you bought a VM iTaste! We’ve got the answers to your questions right here. Everything you need to know to start vaping with your VM Starter Kit.

What’s in your kit?

- A VV battery – It will be about 75% charged so you can use it right away! You can always grab another VM iTaste battery if you need to.
- A magnet adaptor – This is where you connect your clearomisers or cartomisers (510 threaded – Ego threads will not fit)
- A USB passthrough cable
- 5 x VM Mini Clearomisers
- A neat little carry case.

So how do you put it all together and vape?

a) Drop the Magnet into the battery
b) Fill up a VM Mini Clearomiser. If you’re not sure how, read through the guide – Filling your VM Mini Clearomiser
c) Attach the Clearomiser to the Magnet Adaptor
d) Vape Away!

You might notice that the battery isn’t working. This is because it has a safety feature. Click the battery button 3 times quickly to turn the battery on and off. When the battery button glows while pressing it, you know it’s on!

What are these extra buttons for?

The VM iTaste is a Variable Voltage device ranging from 3.3-5.0 volts, adjustable in 0.1 increments. An added feature of the VM iTaste is that it rates your atomiser and tells you the best vaping range!

1) To access the atomiser test and see your recommended voltage range, hold down the + and - buttons simultaneously. It will show 2 different voltages, from lowest to highest. This voltage range is recomended for the atomiser/clearomiser/cartomiser you are using.

2) To change your voltage, press and hold either the + or - button. It will show you a ‘vape’ counter first and then the current voltage. You can then adjust your voltage up or down using the relevant buttons.

Charging your VM iTaste battery

1) Plug the USB passthrough cable into the base of you battery
2) Plug the USB cable end into your computer. You can still vape while the battery is charging!

The battery will take a few hours to charge from the wall and a bit longer if charging from your computer.

If you have any other questions about your VM iTaste Vapermate, just drop us a line in the Contact Us section. We’ll help you out, no worries mate!


VM MadMod Guides

VM ZMAX Scope User Manual

Such an excellent choice! Here’s how to navigate the menu on your new VM ZMAX Scope

To switch the device on/off, press the button 3 times. 

To adjust the voltage/wattage UP, press the button 4 times.

To adjust the voltage/wattage DOWN, press the button 5 times.

To test your battery voltage, press the button 6 times.

To show the voltage/wattage and atomiser resistance, press the button 7 times.

To turn the OLED display on/off, press the button 8 times.

To choose between voltage or wattage, press the button 9 times.

To access the root menu for RMS or Mean Value, press the button 10 times. 

 

MadMod 4.0 Specifications

The 4.0 MadMod Standard and Mini have great features! You wont be disappointed by adding this Mod to your vaping kit.

1. Power lock button (red)

  • Hold the red power button in for 3 seconds to turn the mod on/off.
  • Press the power button 5 times quickly to see the battery voltage.

2. Negative (-) button

  • When you press this button, the voltage will decrease 0.1v between 6.0-3.0v.

3. Positive (+) button

  • When you press this button, the voltage will increase 0.1v between 6.0-3.0v.

4. Vape button (big chrome button)

  • This is a great button! It produces wonderful plumes of tasty vapor goodness.
  • There is a 10 second cut-off protection feature. If you hold the vape button down for more than 10 seconds, the output current stops. Release to vape again.
  • By pressing the vape button 5 times quickly, the LCD screen will show the atomiser resistance.

5. LCD Screen

  • Displays the working voltage between 3.0-6.0v
  • Displays the battery voltage
  • Displays the atomiser resistance
  • You need to recharge the battery when the LCD flashes while holding the vape button. This is a safety feature to let you know that the battery voltage is under 3.0v and time to recharge.

6. Top Connector

  • You can connect 510 and most EGO threaded atomisers, cartomisers and clearomisers without the use of an adaptor.
  • Atomisers suitable for this mod can be 1.5ohm-5-ohm.

NB – The VM Top Coil and Base Coil Clearomisers will require a 510-EGO adaptor to fit the MadMod.

7. Mod Tube

  • You can use high drain or protected batteries.
  • The VM MadMod uses 1 x 18650 (for standard), or 18350 size battery (for mini).

8. End cap

  • Vent hole for added safety in case of battery discharge

Extra Details

3.5amp limit
Output voltage of 3.0-6.0v(+-0.1v)
Short circuit protected current
Quiescent current

Safety Features

Super low quiescent current protection
Reverse battery protection
Over-current protection
Short circuit/atomizer protection
Low voltage warning
Vent hole in base

MadMod Specifics

Diameter: 22mm
Length: 130mm
Weight: 130g
Made of brass, with chrome plating.
All buttons, except the power button (red), are metal.


MadMixes

MadMix Perfection

So you’ve received your MadMix flavours but you’re not quite sure whether you should vape them straight away? No problem! We’ve outlined some optimal steep times to get the most of your MadMixes.

 All ‘Optimal Steep Times’ are based on a complete final mix. If you have chosen STANDARD flavour, the optimal steep time is from the date on the MadMix bottle. If you have chosen DOUBLE flavour, the optimal steep time is from the date you add nicotine to your MadMix.

 The Optimal Steep Times are a guide NOT a rule. There are many factors to consider when letting your MadMixes steep such as: the weather, your storage area or whether you leave the bottle cap on or off. These environmental factors can all speed up or hinder the steeping process.

 The Optimal Steep Times listed in your MadMix flavour description will ensure you have a thoroughly mixed vape. However, if you choose to treat your MadMixes like a fine wine and leave them for weeks, you will be rewarded with an even deeper, smoother vape. Age is exceptionally kind to our MadMixes.

 But really, we can’t blame you if you don’t want to wait weeks, days or even hours so just vape them whenever you want! They still taste awesome straight out of the bottle!


Atomizers

How to Fill your VMT Atomiser

There’s a right way and wrong way to fill your VMT atomiser. Here’s the right way!

1) Remove a cartridge from the packaging.
2) Blow any fluid out of the VMT atomiser. We recommend using a tissue to wipe any excess fluid away. You only need to do this with a new atomiser.
2) Push the empty cartridge into the VMT atomiser. This pops a hole in the silicone plug on the end of the cartridge for you. You only need to do this for each new cartridge.
3) Remove the empty cartridge and take off the silicone end cap (the one you just popped).
4) Squeeze your MadMix into the cartridge about 3/4 of the way full.
5) Replace the end cap.
6) Drip a few drops of MadMix into the VMT atomiser. Try and get the middle needle pin. This primes the atomiser nicely, ready for vaping.
7) Push the filled cartridge into the VMT atomiser. Ensure the cartridge is completely flush with the top of the atomiser.
8) Wait a few seconds to allow the liquid in the cartridge to start wicking into the atomiser.
9) Vape away!

Keep an eye on the liquid level in your cartridge. When it starts to get low, just refill the cartridge again and away you go!

Cleaning your VMT Atomiser

Over time, your VMT atomiser becomes gunked up with all those wonderful MadMix flavours and needs a good clean. Here’s a simple guide to de-crudding your VMT atomiser.

1) Remove the atomiser from the battery
2) Remove the cartridge from the atomiser
3) Blow out any excess MadMix from the atomiser
4) Rinse atomiser under hot water
5) Put atomiser in a glass/cup, on it’s side
6) Pour 1 part white vinegar to 1 part water into the glass. Enough to cover the atomiser is fine.
7) Add 1 teaspoon of Bicarbonate Soda to the glass
9) Let it fizz up nicely.
10) Put thumb and forefinger over the ends of the atomiser, ensuring you’ve got some liquid in the atomiser.
11) Shake the atomiser with the ends covered.
12) Place atomiser back in the glass and let it soak for 10min – 30min.
13) Rinse atomiser thoroughly under hot water.
14) Blow any excess water out of the atomiser
15) Allow 24 hours for atomiser to dry before use or follow ‘dry burn’ instructions at own risk.

How to ‘Dry Burn’ your VMT Atomiser

You don’t always want to wait 24 hours before you can use a clean atomiser and you don’t necessarily have to. There is a quick method used to clean your atomisers but be warned, doing so could void your VapingMad warranty.

Still want to know how? Well okay, it’s simple! Just follow these steps -

1) Follow the atomiser cleaning instructions for your VMT Vapermate.
2) Screw your clean atomiser onto the battery.
3) Without vaping, press and hold the battery button for 6-8 seconds and release.
4) Wait 5-10 seconds
5) Repeat steps 3 and 4. Continue these steps until the atomiser no longer hisses and the wick is glowing red. There should also be no vapour emitting from the atomiser.
NB – This process can take anywhere between 1 – 10minutes, depending on the atomiser.
6) When you’re sure the atomiser is clean and dry, drip a couple of drops of your chosen MadMix directly onto the wick.
7) Assemble your VMT and vape away as normal.

Cleaning your VMTi Atomiser

Over time, your VMTi atomiser becomes gunked up with all those wonderful MadMix flavours and needs a good clean. Here’s a simple guide to de-crudding your VMTi atomiser.

1) Remove the atomiser from the battery.
2) Remove the cartridge from the atomiser.
3) Blow out any excess MadMix from the atomiser.
4) Unscrew the atomiser, so it’s in 2 parts.
5) Rinse each atomiser part under hot water.
6) Put atomiser parts in a glass/cup.
7) Pour 1 part white vinegar to 1 part water into the glass. Enough to cover the atomiser parts is fine.
8) Add 1 teaspoon of Bicarbonate Soda to the glass
9) Let it fizz up nicely.
10) Allow the atomiser parts to soak for 10min – 30min.
11) Rinse atomiser parts thoroughly under hot water.
12) Assemble the atomiser parts and blow any excess water out of the atomiser
13) Allow 24 hours for atomiser to dry before use or follow ‘dry burn’ instructions at own risk.

 

How to ‘Dry Burn’ your VMTi Atomiser

You don’t always want to wait 24 hours before you can use a clean atomiser and you don’t necessarily have to. There is a quick method used to clean your atomisers but be warned, doing so could void your VapingMad warranty.

Still want to know how? Well okay, it’s simple! Just follow these steps -

1) Follow the atomiser cleaning instructions for your VMTi Vapermate.
2) Screw your base atomiser part (the coil) onto the battery.
3) Press and hold the battery button for 6-8 seconds and release.
4) Wait 5-10 seconds
5) Repeat steps 3 and 4. Continue these steps until the atomiser no longer hisses and the coil is glowing red. There should also be no vapour emitting from the atomiser.
NB – This process can take anywhere between 1 – 10minutes, depending on the atomiser.
6) When you’re sure the base atomiser part is clean and dry, drip a couple of drops of your chosen MadMix directly onto the coil.
7) Check the top atomiser part (the wick). You want to the wick to be white/grey. If the ends are a bit charred, you can replace the wick with a spare. Drip a couple of drops onto the clean wick.
8) Assemble your VMTi and vape away.

Cleaning your 306 Atomiser

If you’re constantly changing flavours in your 306 atomiser, you’ll want to make sure it’s clean each time so you get the most out of each new MadMix. Follow these steps to ensure your 306 atomiser vapes like new each time -

1) Remove the atomiser from the battery.
2) Remove the drip tip from the atomiser.
3) Blow out any excess MadMix from the atomiser.
4) Rinse the atomiser under hot water.
5) Put atomiser in a glass/cup.
6) Pour 1 part white vinegar to 1 part water into the glass. Enough to cover the atomiser is fine.
7) Add 1 teaspoon of Bicarbonate Soda to the glass
8) Let it fizz up nicely.
9) Allow the atomiser to soak for 10min – 30min.
10) Rinse atomiser thoroughly under hot water.
11) Assemble the atomiser and blow any excess water out of the atomiser
12) Allow 24 hours for atomiser to dry before use or follow ‘dry burn’ instructions at own risk.

How to ‘Dry Burn’ your 306 Atomiser

You don’t always want to wait 24 hours before you can use a clean atomiser and you don’t necessarily have to. There is a quick method used to clean your atomisers but be warned, doing so could void your VapingMad warranty.

Still want to know how? Well okay, it’s simple! Just follow these steps -

1) Follow the atomiser cleaning instructions for your 306 Atomiser.
2) Screw your clean atomiser onto the battery.
3) Press and hold the battery button for 6-8 seconds and release.
4) Wait 5-10 seconds
5) Repeat steps 3 and 4. Continue these steps until the atomiser no longer hisses and the coil/wick is glowing red. There should also be no vapour emitting from the atomiser.
NB – This process can take anywhere between 1 – 10minutes, depending on the atomiser.
6) When you’re sure the atomiser is clean and dry, you can start dripping as normal. 6 – 8 drops should be good to kick it off!


Cartomisers

How to fill a Cartomiser

You know, one of those long things with white fluffy stuff in it? That’s a cartomiser alright – a cartridge and atomiser in 1 piece. They’re a bit different to fill if you are used to a VMT or VMTi Vapermate but they’re just as easy once you know how to use them properly.

1) Squeeze your MadMix into the top (driptip/mouthpiece end) of the cartomiser. Try and avoid the middle hole as much as possible, it’ll just run straight through.
2) You want to keep filling until MadMix starts coming out of the bottom.
3) Give a quick, short blow into the cartomiser. This will remove any juice from the centre hole.
4) Add more MadMix to the cartomiser, avoiding the centre hole again. If liquid continues to come out the bottom, your cartomiser is full
5) Give another quick, short blow into the cartomiser.
6) It should be ready to go now. Put in the drip tip/mouthpiece and screw the cartomiser onto your battery.
7) Vape away!

The trick with cartomisers is to always keep them moist but not swimming in liquid. You will probably need to top off your cartomiser every couple of hours depending on the size. Remember, practice makes perfect!


Clearomisers

How to ‘dry burn’ your VM Top Coil Clearomiser

Can’t wait to try a new flavour? Perhaps you just want to de-gunk your coil? Not a problem! Follow these easy steps to bring your VM Top Coil back to life!

NB – Dry burn at your own risk, VM does not offer a warranty for failure during or after a ‘dry burn’.

1) Remove the clearomiser from the battery
2) Unscrew the black mouth piece
3) Unscrew the coil head (centre post, silicone covered wicks)
4) Rinse the coil head under hot tap water
5) Rinse the clearomiser tank under hot tap water
6) Pat the coil head dry with a tissue and shake out the excess water in the clearomiser tank. Try and wipe the inside dry as much as possible with a tissue.
7) Screw the clean coil head back into the clearomiser tank (hold the wicks down between thumb and forefinger when putting into the tank)
8) Now screw the assembled tank (without the black mouthpiece) onto your battery
9) Without vaping, press and hold the battery button for 6-8 seconds and release.
10) Wait 5-10 seconds
11) Repeat steps 9 and 10. Continue these steps until the clearomiser no longer hisses and the wick is glowing red. There should also be no vapour or smell emitting from the atomiser.
NB – This process can take anywhere between 1 – 10minutes, depending on the clearomiser.
12) When you’re sure the clearomiser is clean and dry, refill as normal and replace the black mouthpiece
13) Turn clearomiser upside down a couple of times and then vape away as normal.
 
If you don’t want to dry burn, a clean clearomiser can still be achieved but it takes longer. Skip steps 7-11 and instead, leave components out to dry overnight. 24 hours is usually adequate for air drying.

Fill Your Stardust v3 Clearomizer

Want to know how to fill a stardust v3 clearomizer? It’s so easy mate, seriously! Just a few simple steps and you’re vaping!

1) Unscrew the coloured mouthpiece
2) Squeeze your favourite MadMix into the tank. Be careful not to get any in the centre tube.
3) Replace the coloured mouthpiece
4) Vape On!

You may need to turn the Clearomizer upside down briefly to ensure the MadMix wicks properly.

How to fill your VM Base Coil Clearomiser (V1)

Good choice grabbing a VM Base Coil Clearomiser. These things are so easy to use, just read through the simple steps and you’re good to go in 10 seconds!

1) Unscrew the black mouthpiece
2) Push down the white plug
3) Squeeze your madMix into the tank. It’s best to use a blunt needle bottle top or MadMix Injector.
4) Screw the black mouthpiece back on
5) That’s it! Let it sit for a couple of minutes and then Vape On!


DCT System

Filling your DCT system

So you’ve decided that you wanna give the DCT’s a whirl? Nice one! We’ve put together a little guide for you. The steps are suitable for either a standard DCT system or a VMT DCT system.

We’re always updating stuff so keep checking in for more Vapermate information!